A Broadband and ADSL forum. BroadbanterBanter

Welcome to BroadbanterBanter.

You are currently viewing as a guest which gives you limited access to view most discussions and other FREE features. By joining our free community you will have access to post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today.

Go Back   Home » BroadbanterBanter forum » Newsgroup Discussions » uk.telecom.voip (UK VOIP)
Site Map Home Register Authors List Search Today's Posts Mark Forums Read Web Partners

uk.telecom.voip (UK VOIP) (uk.telecom.voip) Discussion of topics relevant to packet based voice technologies including Voice over IP (VoIP), Fax over IP (FoIP), Voice over Frame Relay (VoFR), Voice over Broadband (VoB) and Voice on the Net (VoN) as well as service providers, hardware and software for use with these technologies. Advertising is not allowed.

ASTERISK 2.7 WITH X2 FXO CARDS CONFIGURATION ?



 
 
Thread Tools Display Modes
  #1  
Old January 7th 08, 12:39 PM posted to uk.telecom.voip
phpguy
external usenet poster
 
Posts: 32
Default ASTERISK 2.7 WITH X2 FXO CARDS CONFIGURATION ?

Hello there lads, how do we configure asterisk 2.7 to use x2 fxo cards
for x2 lines ? i got x2 cards installed and only one works and i
configured it according to manual that says::

There is already a trunk called ZAP/g0 edit this
Enter the phone number for you pots line in the Caller ID field
Enter 1 for Maximum channels
Set a dial rule if you want for this trunk
Select an outbound dial prefix to select this trunk when dialing
Set the Zap Identifier to 1 (the default is g0)
This trunk is now configured


all good for one card how do we configure the other ?

cheers

  #2  
Old January 8th 08, 12:22 PM posted to uk.telecom.voip
[email protected]
external usenet poster
 
Posts: 31
Default ASTERISK 2.7 WITH X2 FXO CARDS CONFIGURATION ?

When setting up the second trunk, set the Zap identifier to 2.

Then as root on the Linux box type in:
genzaptelconf
and enter.

type zttools to see the state of you zap trunks

If you're using x100p clone cards you might not get callerID working
on incoming calls....

phpguy wrote:

Hello there lads, how do we configure asterisk 2.7 to use x2 fxo cards
for x2 lines ? i got x2 cards installed and only one works and i
configured it according to manual that says::

There is already a trunk called ZAP/g0 edit this
Enter the phone number for you pots line in the Caller ID field
Enter 1 for Maximum channels
Set a dial rule if you want for this trunk
Select an outbound dial prefix to select this trunk when dialing
Set the Zap Identifier to 1 (the default is g0)
This trunk is now configured


all good for one card how do we configure the other ?

cheers

  #3  
Old January 8th 08, 11:06 PM posted to uk.telecom.voip
phpguy
external usenet poster
 
Posts: 32
Default ASTERISK 2.7 WITH X2 FXO CARDS CONFIGURATION ?

thank you very much for your response

when i want to do outgoing calls which line will be used as default ?
the zap 1 ? if tis busy will the zap 2 be used automatically or not ?

cheers
  #4  
Old January 8th 08, 11:16 PM posted to uk.telecom.voip
Jono
external usenet poster
 
Posts: 1,539
Default ASTERISK 2.7 WITH X2 FXO CARDS CONFIGURATION ?

phpguy explained on 08/01/2008 :
thank you very much for your response

when i want to do outgoing calls which line will be used as default ?
the zap 1 ? if tis busy will the zap 2 be used automatically or not ?


Can't you just select the relevant trunks in your outbound routes page.

Choose ZAP/gO as the first in the sequence..... and the other for the
next in the sequence.


  #5  
Old June 12th 08, 09:47 PM posted to uk.telecom.voip
>
external usenet poster
 
Posts: 18
Default ASTERISK 2.7 WITH X2 FXO CARDS CONFIGURATION ?


"Jono" wrote in message
. ..
phpguy explained on 08/01/2008 :
thank you very much for your response

when i want to do outgoing calls which line will be used as default ?
the zap 1 ? if tis busy will the zap 2 be used automatically or not ?


Can't you just select the relevant trunks in your outbound routes page.

Choose ZAP/gO as the first in the sequence..... and the other for the next
in the sequence.


http://www.doorloadingservices.co.uk


  #6  
Old June 13th 08, 08:04 PM posted to uk.telecom.voip
Jono
external usenet poster
 
Posts: 1,539
Default ASTERISK 2.7 WITH X2 FXO CARDS CONFIGURATION ?

It happens that )))' Orange Peel '((( formulated :
"Jono" wrote in message
. ..
phpguy explained on 08/01/2008 :
thank you very much for your response

when i want to do outgoing calls which line will be used as default ?
the zap 1 ? if tis busy will the zap 2 be used automatically or not ?


Can't you just select the relevant trunks in your outbound routes page.

Choose ZAP/gO as the first in the sequence..... and the other for the next
in the sequence.


http://www.doorloadingservices.co.uk


OK, thanks. Not quite sure of the relevance, though.


 




Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
ASTERISK 2.7 WITH X2 FXO CARDS CONFIGURATION ? phpguy uk.telecom.voip (UK VOIP) 0 January 7th 08 12:39 PM
A different Asterisk & SipDiscount working Configuration (Thanks Sparks) Jono uk.telecom.voip (UK VOIP) 12 November 4th 05 07:15 PM
Network Cards / Video cards SJ uk.comp.home-networking (UK home networking) 4 January 13th 05 08:28 PM
Shares configuration? [L.] uk.comp.home-networking (UK home networking) 0 August 30th 04 10:23 AM
Configuration problem Trench Rat uk.comp.home-networking (UK home networking) 2 August 7th 03 02:44 PM


All times are GMT +1. The time now is 10:23 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.Content Relevant URLs by vBSEO 2.4.0
Copyright 2004-2019 BroadbanterBanter.
The comments are property of their posters.